Satdigitalne.cz

Kód: Vybrat vše

--------------------------------------------------------------------
-- Generic Primary Bootloader 0.1-3847, NI (04:13:33, Feb 17 2009)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 1 (expecting 2)
Poly10: 0x860756E3
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x06
CPU clock: 320 MHz
SIF0: 1024 cols x 8192 rows: 128 MBytes
SIF1: 1024 cols x 8192 rows: 128 MBytes
DRAM: 200 MHz, 2 x 128 MBytes: 256 MBytes
NAND: RDY polling disabled
NAND: (ADF1001D) Hynix SLC, pagesize 2048, blocksize 128k, 128 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 187170 uSec


U-Boot 1.2.0.0428_a (Secondary Bootloader) (Nov 15 2010 - 14:12:45)

CPU: PNX????
Secure boot: disabled
DRAM: 256 MB
NAND: nCS0 (force asserted legacy mode)
NAND: Hynix 128MiB 3,3V 8-bit
NAND: blocksize 128 kB, pagesize 2 kB, oobsize 64, buswidth 8bits
NAND 0x00f20000: bad block
Using default environment

init hdmi on i2c 1 bus.
Net: ip3902
Board Opts: EthOsc HDMI PAL
Splash: done
u-boot startup time so far: 686 msec
Hit any key to stop autoboot:  1  0 

STB225v1 nand#     @ 
Unknown command '@' - try 'help'

STB225v1 nand# run menu
## Error: "menu" not defined

STB225v1 nand# ?
?       - alias for 'help'
askenv  - get environment variables from stdin
base    - print or set address offset
bdinfo  - print Board Info structure
boot    - boot default, i.e., run 'bootcmd'
boota   - find, verify and boot signed kernel image
bootd   - boot default, i.e., run 'bootcmd'
bootm   - boot application image from memory
bootp	- boot image via network using BootP/TFTP protocol
chpart	- change active partition
clearenv- erase environment variables persistent storage
cmp     - memory compare
cp      - memory copy
crc32   - checksum calculation
echo    - echo args to console
exit    - exit script
go      - start application at address 'addr'
help    - print online help
iminfo  - print header information for application image
itest	- return true/false on integer compare
loadb   - load binary file over serial line (kermit mode)
loady   - load binary file over serial line (ymodem mode)
loop    - infinite loop on address range
md      - memory display
mii     - MII utility commands
mm      - memory modify (auto-incrementing)
mtdparts- define flash/nand partitions
mtest   - simple RAM test
mw      - memory write (fill)
nand    - NAND sub-system
nboot   - boot from NAND device
nm      - memory modify (constant address)
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reboot  - Perform RESET of the CPU
reset   - Perform RESET of the CPU
run     - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv  - set environment variables
sha1    - sha1 hash calculation
sleep   - delay execution for some time
splash  - init splash screen
st_aes  - run AES selftest
st_ai   - run aimage selftest
st_ecc  - run NAND ECC selftest benchmark
st_miu  - dump MIU timing
st_sha1 - run sha1 selftest
test    - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
version - print monitor version

STB225v1 nand#